Chat with us, powered by LiveChat Skip to content

PCAN-USB Pro FD Adapter

SKU #: IPEH-004061

The new CAN FD Pro from PEAK-System, PCAN-USB Pro FD adapter enables the connection of CAN FD and LIN networks to a computer via USB. Two field busses can be connected at the same time, up to four with appropriate adapter cables (2 x CAN FD, 2 x LIN). Each CAN FD channel is separately isolated against USB and LIN with a maximum of 500 Volts. Its robust aluminum casing makes the PCAN-USB Pro FD adapter suitable for mobile applications.

The PCAN-USB package includes device drivers for Windows® 11 (64-bit) and 10 (32/64-bit), the PCAN-Basic API, and the PCAN-View CAN monitor software. Linux drivers are also available. For customers needing more sophisticated CAN Analyzing software we have PCAN-Explorer 6.

  • Transmitting and receiving of CAN FD and LIN messages using 2 D-Sub connections (both with pin assignment for the CAN FD and LIN bus)
  • Adapter for High-speed USB 2.0 (compatible to USB 1.1 and USB 3.0)
  • Time stamp resolution 1 μs
  • 5-Volt supply at the D-Sub connector can be activated through a solder jumper, e.g. for external bus converter
  • Voltage supply via USB
  • Extended operating temperature range from -40 to 85 °C (-40 to 185 °F)

CAN operation properties:

  • FPGA implementation of the CAN FD controller
  • Complies with CAN specifications 2.0 A/B and FD 1.0
  • CAN FD bit rates for the data field (64 bytes max.) from 40 kbit/s up to 12 Mbit/s
  • CAN bit rates from 40 kbit/s up to 1 Mbit/s
  • NXP TJA1044GT CAN transceiver
  • Each CAN FD channel is separately opto-decoupled against USB and LIN up to 500 V
  • CAN termination can be activated through a solder jumper
  • Measurement of bus load including error frames and overload frames
  • Induced error generation for incoming and outgoing CAN messages

LIN operation properties:

  • Bit rates from 1 kbit/s up to 20 kbit/s
  • TJA1021/20 LIN transceiver
  • Both LIN channels (common ground) are optodecoupled against USB and CAN FD
  • Can be used as a LIN master or slave (1 ms master task resolution)
  • Automatic bit rate, frame length, and checksum type recognition
  • Autonomous scheduler with support for unconditional, event, and sporadic frames
  • Hardware can work through a schedule table (up to 8 schedule tables can be configured with a total of 256 slots)
Interface(s) PC: USB plug type A, high-speed USB 2.0 (compatible to USB 1.1 and 3.0)
CAN/LIN: CAN FD 1.0 (compatible with CAN 2.0) ISO 11898-2, complies with CiA-recommendation DS 102
Power Consumption USB 5V max. 200 mA
Baud Rate CAN 2.0: 40 kBit/s ... 1 MBit/s; CAN FD: 40 kBit/s ... 12 MBit/s
LIN: 1 kbit/s – 20 kbit/s
Pinout C.I.A. DS-102 (CAN_H = 7, CAN_L = 2, CAN_GND = 3)
Enclosure IP20
Transceiver CAN: TJA1044GT; LIN: TJA1021/22
Dimensions 114 x 71.5 x 24 mm (without connection cable)
Weight 220 g (with USB cable)
Software Driver: Windows® 10, 8.1, 7 and Linux
Tools: PCAN-View for Windows®, PLIN-View Pro
Isolation 500 VDC
Controller(s) FPGA Implementation
Connector(s) USB
Timestamp Resolution 1 microsecond
Specification CAN/LIN: CAN FD 1.0, CAN 2.0A (Standard format) and 2.0B (extended format) , LIN specification 2.1
Operating temperature -40°C to +85°C
Storage temperature -40°C to +100°C
Relative humidity 15% to 90% (non-condensing)
EMC directives EN 55024:2011-09
EN 55022:2011-12
EC directive 2004/108/EG
Certifications CE, RoHS
PCAN-USB Pro FD manual
User's Manual in English
Device driver setup for Windows
Installation package from PEAK-System for device drivers and tools for Windows ® 10, 8.1 (32/64-bit) for our PC interfaces. Tools included: PEAK-CPL, PCAN-View, PLIN-View Pro and Virtual PCAN-Gateway.
Device drivers for Linux
Device driver for PEAK CAN interfaces from Kernel 2.6.
PCAN-USB Pro FD firmware
Firmware upgrade
PCAN-View
Software for displaying, sending and recording CAN and CAN FD messages for Windows ® 10, 8.1 (32/64-bit).
PCAN-Basic API
API for developing applications with CAN and CAN FD connections for Windows ® 10, 8.1 (32/64-bit).
PCAN-Basic API (Linux)
API for developing applications with CAN connection for Linux.
PLIN-API
API for the development of applications with LIN connection for Windows® 11 (64-bit), 10 (32/64-bit).
PCAN-CCP API
API for developing software for communication with control units according to the CAN Calibration Protocol (CCP) for Windows ® 10, 8.1 (32/64-bit).
PCAN-XCP API
API for developing software for communication with ECUs in accordance with the Universal Measurement and Calibration Protocol (XCP) for Windows ® 10, 8.1 (32/64-bit).
PCAN-ISO-TP API
API for the transmission of data packets according to ISO-TP (ISO 15765-2) for Windows ® 10, 8.1 (32/64-bit).
PCAN-UDS API
API for communication with control units according to UDS (ISO 14229-1) for Windows ® 10, 8.1 (32/64-bit).
PCAN-OBD-2 API
API for vehicle diagnosis according to OBD-2 (ISO 15765-4) for Windows ® 10, 8.1 (32/64-bit).
PCAN-PassThru API
Pass-Thru API and connection of Pass-Thru software to PEAK-CAN interfaces. Installation for Windows ® 10, 8.1 (32/64-bit) including interface DLLs, configuration software, PCAN-Basic API and PCAN-ISO-TP API. Documentation included in the download.
The new CAN FD Pro from PEAK-System, PCAN-USB Pro FD adapter enables the connection of CAN FD and LIN networks to a computer via USB. Two field busses can be connected at the same time, up to four ...